My new lathe sanding station
-
- Posts: 2244
- Joined: Thu Oct 22, 2015 4:51 pm
My new lathe sanding station
Since turning is not a very common operation in my workshop, I've thought about getting more use out of the engine by adding a Belt Sander and a small Thickness Sander.
More info:
More info:
-
- Posts: 7
- Joined: Fri Nov 11, 2016 4:21 pm
My new lathe sanding station
Excelente, como siempre es digno de admirar tu trabajo.
te felicito, y quedo a la espera de mas, jajajajaa.
te admiro y por eso te sigo.
Abrazo.
te felicito, y quedo a la espera de mas, jajajajaa.
te admiro y por eso te sigo.
Abrazo.
-
- Posts: 7
- Joined: Fri Nov 11, 2016 4:21 pm
My new lathe sanding station
Hola, yo nuevamente, acabo de mirar el segundo video, admirable, simple, prolijo y perfecto.
como siempre, es una sorpresa y un deleite, seguir tus trabajos.
nuevamente Felicitaciones.
como siempre, es una sorpresa y un deleite, seguir tus trabajos.
nuevamente Felicitaciones.
-
- Posts: 2244
- Joined: Thu Oct 22, 2015 4:51 pm
My new lathe sanding station
muchas gracias Sergio!
me alegra que te gusten mis diseños.
me alegra que te gusten mis diseños.
-
- Posts: 7
- Joined: Fri Nov 11, 2016 4:21 pm
My new lathe sanding station
Hola Suso, buenos dias.
ademas de felicitarte de nuevo jajaja, queria preguntarte, si el sistema de aspiracion que implementaste, es suficiente???
va, no se, que aspirador tienes, si uno comercial o uno casero, es que tambien estoy tratando de fabricar mi "duster colector", jajaja.
bueno muy buen trabajo, impecable como siempre.
un abrazo.
a ya que estamos, me gustaria que en un futuro comiences el diseño de una sierra sinfin, mediana, jajaja perdon por pedir jajaja, pero siempre haces lo mejor y seria interesante de ver, eso confeccionado por ti.
ahora si, no molesto mas, felicitaciones.
ademas de felicitarte de nuevo jajaja, queria preguntarte, si el sistema de aspiracion que implementaste, es suficiente???
va, no se, que aspirador tienes, si uno comercial o uno casero, es que tambien estoy tratando de fabricar mi "duster colector", jajaja.
bueno muy buen trabajo, impecable como siempre.
un abrazo.
a ya que estamos, me gustaria que en un futuro comiences el diseño de una sierra sinfin, mediana, jajaja perdon por pedir jajaja, pero siempre haces lo mejor y seria interesante de ver, eso confeccionado por ti.
ahora si, no molesto mas, felicitaciones.
-
- Posts: 2244
- Joined: Thu Oct 22, 2015 4:51 pm
My new lathe sanding station
Hola Sergio,
tengo un aspirador muy viejo y normalito del Lidl, no aspira gran cosa y aún así con este diseño apenas deja escapar nada de polvo. Tengo en mente hacerme con otro, o al igual que tu fabricarme mi propio "duster colector" y de este modo te puedo asegurar que será mas que suficiente!
La sierra de banda es uno de mis proyectos pendientes, espero que pueda llevarlo a cabo este año...debes estar atento! :D
tengo un aspirador muy viejo y normalito del Lidl, no aspira gran cosa y aún así con este diseño apenas deja escapar nada de polvo. Tengo en mente hacerme con otro, o al igual que tu fabricarme mi propio "duster colector" y de este modo te puedo asegurar que será mas que suficiente!
La sierra de banda es uno de mis proyectos pendientes, espero que pueda llevarlo a cabo este año...debes estar atento! :D
-
- Posts: 3
- Joined: Sun Aug 02, 2015 4:04 am
My new lathe sanding station
Hi Suso,
Daniel from France ... so I finally bought the plans for the Lathe, waiting for the thickness sander ones too.
A few comment, first w.r.t. the rotation, for the lathe that's normal, but I think for the thickness sander it would make more sense
to bring the wood piece down i.e. push from the other side. but that require the motor to run in the other direction, something
doable on most engine by providing a switch to select which pole the condo attaches to, something I will have to play with.
I was also pondering having the motor below the lathe, to take less space but that requires weakening the assembly of the
frame to let the belt go. Something else I need to think about before starting the project for good, very tempted to have a different
attachment for the motor, more like Mathias Wandel's lathe, allowing a larger range of rotation speed choices.
Can't find connector nuts in my area for that diameter of rod, so likely to just solder normal nuts together, hope that will work ...
So still a few thing to think through before I start for good, thanks again for the inspiration :-)
Daniel
Daniel from France ... so I finally bought the plans for the Lathe, waiting for the thickness sander ones too.
A few comment, first w.r.t. the rotation, for the lathe that's normal, but I think for the thickness sander it would make more sense
to bring the wood piece down i.e. push from the other side. but that require the motor to run in the other direction, something
doable on most engine by providing a switch to select which pole the condo attaches to, something I will have to play with.
I was also pondering having the motor below the lathe, to take less space but that requires weakening the assembly of the
frame to let the belt go. Something else I need to think about before starting the project for good, very tempted to have a different
attachment for the motor, more like Mathias Wandel's lathe, allowing a larger range of rotation speed choices.
Can't find connector nuts in my area for that diameter of rod, so likely to just solder normal nuts together, hope that will work ...
So still a few thing to think through before I start for good, thanks again for the inspiration :-)
Daniel
-
- Posts: 2244
- Joined: Thu Oct 22, 2015 4:51 pm
My new lathe sanding station
hi again Daniel!
Regarding to the rotation of the engine, it is a good idea! I was also thinking about it, but it is quite difficult to do with my engine. There are engines which allow you to easily change the rotation, and you'll get a lathe much more versatile.
If you are going to introduce the pieces in the thickness sander from the front, you should make the tilting table much longer, because you don't have enough support at the front on the thickness sander. I think it can also serve as I did.
Regarding putting the engine under the lathe, it depends on the design you have in mind, it could be done but the way I did it also works, it is also a good idea to get a larger range of rotation speed choices.
Remember to use a perfectly straight threaded rod, some are more crooked than others, and perfectly align all bearings.
Here you can find the M20 connector nuts, I do not think it's a good idea to weld two normal nuts.
Regarding to the rotation of the engine, it is a good idea! I was also thinking about it, but it is quite difficult to do with my engine. There are engines which allow you to easily change the rotation, and you'll get a lathe much more versatile.
If you are going to introduce the pieces in the thickness sander from the front, you should make the tilting table much longer, because you don't have enough support at the front on the thickness sander. I think it can also serve as I did.
Regarding putting the engine under the lathe, it depends on the design you have in mind, it could be done but the way I did it also works, it is also a good idea to get a larger range of rotation speed choices.
Remember to use a perfectly straight threaded rod, some are more crooked than others, and perfectly align all bearings.
Here you can find the M20 connector nuts, I do not think it's a good idea to weld two normal nuts.
-
- Posts: 3
- Joined: Sun Aug 02, 2015 4:04 am
My new lathe sanding station
Thanks suso for all the informations. BTW for the coupling nuts most vendors around amazon are horribly
expensive (15 Euro for sending a nut !) I found way cheaper on Ebay for europeans:
The key for the search is M20 for diameter and add "DIN 6334" as this kind of coupler seems standardized :-)
Local hardware stores had couplers but cylindrical and only for smaller diameters.
Yours,
Daniel
expensive (15 Euro for sending a nut !) I found way cheaper on Ebay for europeans:
The key for the search is M20 for diameter and add "DIN 6334" as this kind of coupler seems standardized :-)
Local hardware stores had couplers but cylindrical and only for smaller diameters.
Yours,
Daniel
-
- Posts: 1
- Joined: Wed Mar 15, 2017 9:41 pm
My new lathe sanding station
Hola, ingresé a esta pagina por un video e hice mi cuenta pero no entiendo mucho del video.
Tengo dudas y no se si estoy consultando bien.
¿que caracteristicas tiene el motor que se usa en el video de torno lijadora?
Tengo dudas y no se si estoy consultando bien.
¿que caracteristicas tiene el motor que se usa en el video de torno lijadora?